Mazda 6 Forums banner
1-11 of 11 Results
  1. Newbie Section
    I have a 2004 2.3l mazda 3 hatchback engine looking at a 2007 hatchback that has a blown engine. Can i swap out the 2007 engine with the 2004 engine?
  2. Engine / Suspension / Drivetrain
    Hello guys, I've noticed this rattle coming from the engine. (2007 2.3l) It's especially present at cold start and then around 2-3000 rpm. Car has done about 300.000km and have had oil and filter changes regularly. I've looked around ind the forum but haven't been able to diagnose the exact...
  3. Speed6 Engine/Drivetrain
    So, I was driving my speed6 yesterday and the turbo caught fire (probably the seals, go figure with this car). I noticed something was wrong pretty quickly and the FD got there really fast (whole thing went down within less than 10 mins between me seeing smoke and them putting it out) so theres...
  4. 2nd-Gen
    Hi guys, so I've been having some trouble with my mid 2006 2.3L 4 cylinder (180k Km) ignition coil. A couple days ago I had just driven about 30min to drop someone off, turned around and felt a misfire, the check engine light was flashing so I pulled over and ran a scan and it was a misfire in...
  5. Newbie Section
    Hi, Folks. Today was my 1st official day with my ‘04 Mazda 6s Squall Blue Wagon, with about 137,700 miles on the odo. After replacing a blown engine with a 6 month/6,000 warranted LKQ engine with 107,000 miles, I took an 85 mile trip over hill and dale, It was great learning the +s and -s of the...
  6. 2.0 Diesel
    Hi everyone! My car is Mazda 6, 2005, 2.0, Diesel, 136 hp, Manual gears, Station Wagon. For the past 4-5 days the following issue has started to occur: When I start the engine for the first time in the morning, it would run for a few second and it will die. The second time I try to start it...
  7. 3.0L V6
    Could someone please help me out? I have an 06 mazda 6 3.0L that will crank, but the engine won't start! Here's some info: -car has about 190k miles on it -overheated in Decmeber, so I replaced the water pump, radiator, and a few cracked hoses -serpentine belt a little loose because of an oil...
  8. Consumer Reviews
    I've searched high and low for 2.3 l connecting rod bolts, but haven't been able to find anything. Not on-line, not at Mazda, not at Ford. Can anyone help? Thank you in advance!
  9. 3rd-Gen
    Yesterday I sit in my 2017 manual. I think, "Let me see how engine sound if revved hard", for the first time in 2.5 years. Bum! At 4K rpm it is done, can't go no more. Then, I tried it again while in neutral with car moving - voila. Can rev passed 4K
  10. 2.3L I-4
    2007 Mazda 6i. Auto. Got Reman engine, but now when mating trans, the torque converter bolts contact block. I’ve pushed the converter as far into the trans, so nothing protrudes past front of trans. As soon as I torque the trans the bolts rub. I can’t figure out why there is not enough...
  11. 2.5L I-4
    I have 2012 Mazda 6 2nd generation with 2.5l engine. When car is parked the engine is fine even in max rpm-s without any extra noise. But while driving with heavy weight or on uphills the engine gives some strange noise on any gear. I have recorded the sound which can be listened on the link...
1-11 of 11 Results