Mazda 6 Forums banner

Search results

1-20 of 494 Results
Advanced Search
  1. Rob Frm Utah

    Newbie Section
    Welcome. I'm in Utah as well.
  2. Runs very rough after turning engine off and back on after warm?

    2.3L I-4
    Flashing CEL indicates misfire. The plugs you pulled did they have oil on them? Pull the two center plugs and check them. If they do you need a valve cover gasket. I'll bet that's what it is.
  3. Mazda 6 Projector upgrade DDMTUNING

    Exterior Modifications
    After doing some research it looks like those are the old versions of the mini's TRS used to sell. TRS has revised there's a few times since and made them better. I believe TRS is on the sixth revision.
  4. Engine revs up and down

    Newbie Section
    My money is on the upstream 02 sensor or the Throttle body. You can check the upstream 02 by unplugging it. The plug is underneath the car near the driverside door. It's easy to follow the wires.
  5. Mazda 6 Projector upgrade DDMTUNING

    Exterior Modifications
    Those projectors look like the old H1 mini's TRS used to sell.
  6. +.5mm Bore?

    2.3L I-4
    Yes. .5 is plenty. You'll need to figure out tuning. Currently for your year there are only standalone options that I'm aware of.
  7. Looking for DIY on inner tie rods

    Suspension / Brakes
    No. The lock washer comes locked on a new tie rod. No need to worry about pushing it on. It should already be hooked to the tie rod pre install. My stock tie rods did not have Loctite on them when I took them off so I didn't put any one when I installed new ones so use at your own...
  8. Looking for DIY on inner tie rods

    Suspension / Brakes
    Just use a screw driver to pry the lock washer back. Rent the tie rod tool from whatever local auto parts stores you have near you. It's a pretty easy install as longs as your outer tie rods come off okay.
  9. Highest Horsepower

    Mazdaspeed6
    Reported as spam.
  10. 6Y Mazda's 1996 Miata

    Picture/Videos
    I only came back to check out this thread. Looking good. Camber is kinda crazy!
  11. Is this intake manifold any good?

    2.3L I-4
    Unless you are building a drag car, boosting your car or just want engine bling I would not buy an after market intake mani. They have very high flow. Good for high end power but bad for low end torque and power.
  12. Msds header

    2.3L I-4
    no/yes. Front o2 sensor is wideband. They will be fine. If you get a CEL which you shouldn't if you are leaving the main cat then you can absolutely return it to stock and reset the code.
  13. Performance Chips

    2.3L I-4
    Please don't take the internet too seriously. It was a joke. Want tuning? Your options are below for any 06-08 6i Hypertech(flash but not unlocked to the user) PowerMod Sequential(Piggyback) Megasquirt 2(standalone) MazdaEdit(flash, some drivers not supported yet)
  14. Performance Chips

    2.3L I-4
    This is the only performance chip that you need. ZuperChips
  15. ~~ The official "What did you do to your 6 today" thread!! ~~

    Mazda6 (Atenza)
    Lol turning rubs on bumps. Yeah I ended up getting them. I had to do something. I bought stock suspension from someone on here that turned out to be bad.
  16. Tips on aiming headlights

    Electrical / HVAC
    It's not unreachable. Just not easy. I've never removed them from the car to adjust.
  17. ~~ The official "What did you do to your 6 today" thread!! ~~

    Mazda6 (Atenza)
    I'm running 245/40
  18. ~~ The official "What did you do to your 6 today" thread!! ~~

    Mazda6 (Atenza)
    These are them. They take a bit of work to get them to fit and you definitely have to be lowered for them...
  19. ~~ The official "What did you do to your 6 today" thread!! ~~

    Mazda6 (Atenza)
    All new front control arms and tie rods. New tires and decided to powder coat my wheels something new.
  20. mazda 6 2008 clicking

    Newbie Section
    Azhure what model do you have? If four cylinder typically clicking or ticking on start up has a lot to do with the VVT tensioner. The speeds are not the only ones that get bad ones. Generally it does not last one minute but 10-15 seconds on start up.
1-20 of 494 Results
Top